Opel Omega

since 1993-1999 of release

Repair and car operation

Opel Omega
+ 1. Maintenance instruction
+ 2. Maintenance
- 3. Repair of engines
   + 3.1. SOHC engines in volume 2,0 liters
   + 3.2. DOHC engines in volume 2,0 liters
   + 3.3. Engines in volume 2,5 and 3,0 liters
   + 3.4. Partition of all petrol engines
   - 3.5. Diesel engine in volume 2,0 liters
      3.5.1. Technical characteristics
      3.5.2. Repair operations on the engine established in the car
      3.5.3. Check of pressure of compression 3_5_4.htm
      3.5.5. Gazoraspredeleniye mechanism
      3.5.6. Cover of a head of the block of cylinders
      3.5.7. Pulley of a cranked shaft
      3.5.8. Chain cover
      3.5.9. Natyazhiteli of a chain
      3.5.10. Chains and asterisks
      3.5.11. Camshafts and pushers
      3.5.12. Head of the block of cylinders
      3.5.13. Oil pallet
      3.5.14. Oil pump
      3.5.15. Oil radiator
      3.5.16. Sealing rings of a cranked shaft
      3.5.17. Flywheel
      3.5.18. Suspension brackets of the power unit
      - 3.5.19. Major maintenance of the diesel engine in volume 2,0 liters
         3.5.19.1. Technical characteristics
         3.5.19.2. Head of the block of cylinders
         3.5.19.3. Pistons and rods
         3.5.19.4. Cranked shaft
         3.5.19.5. Block of cylinders of the engine
         3.5.19.6. Radical bearings and bearings of rods
         3.5.19.7. Engine balance of assembly at major maintenance
         3.5.19.8. Piston rings
         3.5.19.9. Working gaps of radical bearings
         3.5.19.10. Working gaps of shatunny bearings
         3.5.19.11. Engine start after major maintenance
   + 3.6. Diesel six-cylinder 2,5-liter engine
+ 4. Heating system and ventilation
+ 5. Fuel, exhaust systems
+ 6. System of start of the engine
+ 7. Ignition system
+ 8. Coupling
+ 9. Transmissions
+ 10. Main transfer, semi-axes
+ 11. Brake system
+ 12. Suspension bracket and steering
+ 13. Body
+ 14. Body electric equipment

3.5.19.9. Working gaps of radical bearings

GENERAL INFORMATION

Use both standard radical bearings of a cranked shaft, and radical bearings with the reduced size is possible. The demanded size of the bearing can be defined after measurement of a neck of a cranked shaft.

Check

PERFORMANCE ORDER

1. Clear a back part of the loose leaf and a place of its installation in the block of cylinders and covers of radical bearings.
	2. Establish loose leaves on the places, thus a ledge on the loose leaf it should be combined with a groove on a cover (it is specified by an arrow).
3. One of methods which assumes micrometer existence for measurement of diameter of openings, consists in establishing covers of radical bearings together with the loose leaf on the block of cylinders and to screw them the demanded moment. Measure internal diameter of each collected pair of loose leaves of bearings. Measure diameter of each radical neck of a cranked shaft. Subtract from the measured diameter of the bearing the corresponding diameter of a radical neck of a cranked shaft.
4. The second (and more exact) a method consists in using a product known as for Plastigage. It is a round plastic core which is compressed between the loose leaf and a neck of a cranked shaft. After removal of a cover of the radical bearing the deformed plastic core is measured by a special template which is available in Plastigage set. On established in the block of cylinders loose leaves establish without greasing a cranked shaft. Necks of a cranked shaft and loose leaves should be absolutely pure and dry.
	5. Cut off some slices of a plastic core of Plastigage (they should be slightly shorter, than width of the main bearings) and establish on each neck of a cranked shaft.
6. Establish covers with the bottom loose leaves and tighten bolts of fastening the demanded moment. In the course of gap measurement by the Plastigage method do not rotate a cranked shaft.
	7. Unscrew a cover of fastening of the loose leaf, remove it and to the deformed plastic core put a large-scale ruler. Comparing width of the deformed plastic core with control width on a large-scale ruler, define gap size.
8. In end carefully clear Plastigage-material traces from loose leaves and a cranked shaft.