Opel Omega

since 1993-1999 of release

Repair and car operation



Opel Omega
+ 1. Maintenance instruction
+ 2. Maintenance
- 3. Repair of engines
   + 3.1. SOHC engines in volume 2,0 liters
   + 3.2. DOHC engines in volume 2,0 liters
   + 3.3. Engines in volume 2,5 and 3,0 liters
   + 3.4. Partition of all petrol engines
   - 3.5. Diesel engine in volume 2,0 liters
      3.5.1. Technical characteristics
      3.5.2. Repair operations on the engine established in the car
      3.5.3. Check of pressure of compression 3_5_4.htm
      3.5.5. Gazoraspredeleniye mechanism
      3.5.6. Cover of a head of the block of cylinders
      3.5.7. Pulley of a cranked shaft
      3.5.8. Chain cover
      3.5.9. Natyazhiteli of a chain
      3.5.10. Chains and asterisks
      3.5.11. Camshafts and pushers
      3.5.12. Head of the block of cylinders
      3.5.13. Oil pallet
      3.5.14. Oil pump
      3.5.15. Oil radiator
      3.5.16. Sealing rings of a cranked shaft
      3.5.17. Flywheel
      3.5.18. Suspension brackets of the power unit
      + 3.5.19. Major maintenance of the diesel engine in volume 2,0 liters
   + 3.6. Diesel six-cylinder 2,5-liter engine
+ 4. Heating system and ventilation
+ 5. Fuel, exhaust systems
+ 6. System of start of the engine
+ 7. Ignition system
+ 8. Coupling
+ 9. Transmissions
+ 10. Main transfer, semi-axes
+ 11. Brake system
+ 12. Suspension bracket and steering
+ 13. Body
+ 14. Body electric equipment
d0mik.ru



3.5.9. Natyazhiteli of a chain

TOP NATYAZHITEL

Removal

PERFORMANCE ORDER
1. Remove a casing of the air filter.
2. Unscrew a bolt of fastening of the right support of the engine from a head of the block of cylinders.
3. Unscrew a head of the mechanism of a tension from a back part of a head of the block of cylinders.
4. Take a plunzher of the mechanism of a tension.

Prevention

Do not turn a cranked shaft of the engine at removal of the mechanism of a tension.


5. Examine a plunzher of the mechanism of a tension on existence of wear or damages and, if necessary, replace it.

Installation

PERFORMANCE ORDER
1. Grease a plunzher of the mechanism of a tension with pure engine oil and insert it into a head of the block of cylinders.
2. Establish a new sealing ring to a head of the mechanism of a tension (it is specified by an arrow).
3. To Nazhamita a head of a plunzher of the mechanism of a tension before click for the correct adjustment of the mechanism of a tension. Screw up a head, having tightened the demanded moment.
4. Establish the right suspension bracket of the power unit.
5. Establish a casing of the air filter.

BOTTOM NATYAZHITEL OF THE CHAIN

Removal

PERFORMANCE ORDER
1. Lift a forward part of the car and fix on supports.
2. Unscrew a head of the mechanism of a tension of the bottom chain.
3. Take a plunzher.

Prevention

Do not turn a cranked shaft of the engine at removal of the mechanism of a tension.


4. Examine a plunzher of the mechanism of a tension on existence of wear and damages and, if necessary, replace it.

Installation

PERFORMANCE ORDER
1. Grease a plunzher (it is specified by an arrow) the tension mechanism pure engine oil and insert it into place.
2. Establish a head of the bottom mechanism of a tension with a new sealing ring and tighten it the demanded moment. If the new mechanism of a tension is established, press a pin in the central part of a head before click therefore the pin should be pressed and come back to a place easily.