Opel Omega

since 1993-1999 of release

Repair and car operation

Opel Omega
+ 1. Maintenance instruction
+ 2. Maintenance
- 3. Repair of engines
   + 3.1. SOHC engines in volume 2,0 liters
   + 3.2. DOHC engines in volume 2,0 liters
   + 3.3. Engines in volume 2,5 and 3,0 liters
   + 3.4. Partition of all petrol engines
   - 3.5. Diesel engine in volume 2,0 liters
      3.5.1. Technical characteristics
      3.5.2. Repair operations on the engine established in the car
      3.5.3. Check of pressure of compression 3_5_4.htm
      3.5.5. Gazoraspredeleniye mechanism
      3.5.6. Cover of a head of the block of cylinders
      3.5.7. Pulley of a cranked shaft
      3.5.8. Chain cover
      3.5.9. Natyazhiteli of a chain
      3.5.10. Chains and asterisks
      3.5.11. Camshafts and pushers
      3.5.12. Head of the block of cylinders
      3.5.13. Oil pallet
      3.5.14. Oil pump
      3.5.15. Oil radiator
      3.5.16. Sealing rings of a cranked shaft
      3.5.17. Flywheel
      3.5.18. Suspension brackets of the power unit
      + 3.5.19. Major maintenance of the diesel engine in volume 2,0 liters
   + 3.6. Diesel six-cylinder 2,5-liter engine
+ 4. Heating system and ventilation
+ 5. Fuel, exhaust systems
+ 6. System of start of the engine
+ 7. Ignition system
+ 8. Coupling
+ 9. Transmissions
+ 10. Main transfer, semi-axes
+ 11. Brake system
+ 12. Suspension bracket and steering
+ 13. Body
+ 14. Body electric equipment

3.5.13. Oil pallet

Removal

PERFORMANCE ORDER

1. Remove a weight wire from the accumulator.
2. Lift a forward part of the car and fix on supports.
3. Merge engine oil. Establish a new washer on a masloslivny stopper and establish a stopper in the oil pallet, having tightened it the demanded moment.
	4. Disconnect electric sockets from sensors of temperature and oil level (it is specified by an arrow).
	5. Unscrew fastening bolts (are specified by shooters) ledge of the oil pallet to a transmission case.
6. Gradually and consistently unscrew bolts of fastening of the oil pallet to the block of cylinders. Remove the oil pallet and laying.
	7. Unscrew a bolt of fastening of a pipe of a maslopriyemnik and check a condition of the mesh filter (bolts of fastening are specified by shooters).

Installation

PERFORMANCE ORDER

1. Clear all traces of oil and dirt from interfaced surfaces of the pallet and the block of cylinders.
2. Establish a new sealing ring on a pipe of a maslopriyemnik and establish a pipe into place.
	3. Apply a thin film hermetic on the bottom surface of the block of cylinders interfaced to the oil pump and a back main cover of the bearing.
	4. Apply a thin film hermetic on the lower part of the block of cylinders interfaced to a back cover of the radical bearing. Places of drawing of hermetic are specified by shooters.
	5. Establish laying on the oil pallet and establish laying on the block of cylinders. Fix the oil pallet bolts.
6. Working from the center in diagonal sequence, tighten bolts of fastening of the oil pallet.
7. Screw up bolts of fastening of a ledge of the oil pallet to a transmission case.
8. Connect electric sockets to sensors of temperature and oil level.
9. Lower the car and fill in engine oil in the engine.