Opel Omega

since 1993-1999 of release

Repair and car operation



Opel Omega
+ 1. Maintenance instruction
+ 2. Maintenance
- 3. Repair of engines
   + 3.1. SOHC engines in volume 2,0 liters
   + 3.2. DOHC engines in volume 2,0 liters
   - 3.3. Engines in volume 2,5 and 3,0 liters
      3.3.1. Technical characteristics
      3.3.2. Compression check
      3.3.3. Top dead point (VMT) of the N1 piston
      3.3.4. Covers of camshafts
      3.3.5. Pulley of a cranked shaft
      3.3.6. Covers of a gas-distributing belt
      3.3.7. Gas-distributing belt
      3.3.8. Natyazhitel of a belt, asterisks and intermediate pulleys
      3.3.9. Epiploons of camshafts
      3.3.10. Camshafts and pushers
      3.3.11. Head of cylinders
      3.3.12. Oil pallet
      3.3.13. Oil pump
      3.3.14. Oil radiator
      3.3.15. Flywheel and leading disk
      3.3.16. Epiploons of a cranked shaft
      3.3.17. Engine and transmission fastenings
   + 3.4. Partition of all petrol engines
   + 3.5. Diesel engine in volume 2,0 liters
   + 3.6. Diesel six-cylinder 2,5-liter engine
+ 4. Heating system and ventilation
+ 5. Fuel, exhaust systems
+ 6. System of start of the engine
+ 7. Ignition system
+ 8. Coupling
+ 9. Transmissions
+ 10. Main transfer, semi-axes
+ 11. Brake system
+ 12. Suspension bracket and steering
+ 13. Body
+ 14. Body electric equipment




3.3.6. Covers of a gas-distributing belt

EXTERNAL COVER

Removal

PERFORMANCE ORDER
1. Remove the preliminary chamber of multiline system of a fence of air (see subsection 5.1.15).
2. Remove a forward connecting tube of secondary system of an admission of air.
3. Remove an additional driving belt.
4. Stop a shaft of the water pump a wrench and unscrew bolts of a pulley of the water pump.
5. Remove a pulley of the water pump. In an installation time new bolts will be necessary for you.
6. Stop a pulley of the pump of the hydraulic booster of a steering and unscrew pulley bolts.
7. Remove a pulley. In an installation time new bolts will be necessary for you.
8. Disconnect a wire from the sensor of the right number of cylinders and disconnect a wire from a cover of a gas-distributing belt.
9. Disconnect the top parts of the holder of a plait of wires which is fixed in a forward part of a cover of a gas-distributing belt. Remove a forward cover (drawing at the left) and the right cover (drawing on the right) the holder of a plait of wires.
10. Disconnect a wire from the valve of adjustment of exhaust gases, unscrew bolts and remove the holder of a plait of wires.
11. Unscrew bolts and remove a natyazhitel of an additional belt.
12. Unscrew bolts and remove an external cover of a gas-distributing belt.

Installation

Installation is carried out to sequences, return to removal.

BACK COVER

Removal

PERFORMANCE ORDER
1. Remove a gas-distributing belt.
2. Remove asterisks of camshafts, remove a pulley of a natyazhitel of a gas-distributing belt and intermediate pulleys.
3. Remove the water pump.
4. Unscrew fixing bolts of a back cover and uncover.

Installation

Installation is carried out to sequences, return to removal.