Opel Omega

since 1993-1999 of release

Repair and car operation

Opel Omega
+ 1. Maintenance instruction
+ 2. Maintenance
- 3. Repair of engines
   + 3.1. SOHC engines in volume 2,0 liters
   + 3.2. DOHC engines in volume 2,0 liters
   - 3.3. Engines in volume 2,5 and 3,0 liters
      3.3.1. Technical characteristics
      3.3.2. Compression check
      3.3.3. Top dead point (VMT) of the N1 piston
      3.3.4. Covers of camshafts
      3.3.5. Pulley of a cranked shaft
      3.3.6. Covers of a gas-distributing belt
      3.3.7. Gas-distributing belt
      3.3.8. Natyazhitel of a belt, asterisks and intermediate pulleys
      3.3.9. Epiploons of camshafts
      3.3.10. Camshafts and pushers
      3.3.11. Head of cylinders
      3.3.12. Oil pallet
      3.3.13. Oil pump
      3.3.14. Oil radiator
      3.3.15. Flywheel and leading disk
      3.3.16. Epiploons of a cranked shaft
      3.3.17. Engine and transmission fastenings
   + 3.4. Partition of all petrol engines
   + 3.5. Diesel engine in volume 2,0 liters
   + 3.6. Diesel six-cylinder 2,5-liter engine
+ 4. Heating system and ventilation
+ 5. Fuel, exhaust systems
+ 6. System of start of the engine
+ 7. Ignition system
+ 8. Coupling
+ 9. Transmissions
+ 10. Main transfer, semi-axes
+ 11. Brake system
+ 12. Suspension bracket and steering
+ 13. Body
+ 14. Body electric equipment

3.3.12. Oil pallet

GENERAL INFORMATION

Places of drawing of hermetic

Removal

PERFORMANCE ORDER

Pallet
1. Disconnect a wire of the minus plug of the accumulator.
2. Lift and fix a forward part of the car.
3. Merge engine oil.
	4. Disconnect a wire from the sensor of level of oil, remove a lock ring and press the sensor socket inside.
5. Unscrew bolts and remove the oil pallet together with laying.
6. If necessary unscrew bolts and remove a maslozaborny branch pipe.
Cast part of the pallet
7. Disconnect a wire from the sensor of the monitoring system of level of the car and disconnect a rod from sharnirny connection of the lever of the sensor.
8. Remove connecting draft of a steering drive.
9. Unscrew bolts and remove shock-absorbers of the right and left support of the engine. Braid the nuts, fixing left and right support of the engine to a body.
10. Fix the engine on the lift.
11. Unscrew forward bolts of a cross-piece of a forward suspension bracket on four turns. Fix a back part of a cross-piece by means of a jack and unscrew back bolts. Lower a back part of a cross-piece approximately on 10 see.
12. Unscrew the bolts, fixing a cast part of the pallet to a transmission and to the block of cylinders. Remove a cast part of the pallet.

Installation

PERFORMANCE ORDER

Pallet
1. Carefully clean being joined surfaces of both parts of the pallet and the block of cylinders.
	2. Before establishing a maslozaborny branch pipe, replace a sealing ring. Establish a maslozaborny branch pipe.
	3. Establish new laying of the pallet, insert the socket of the sensor of level of oil into an opening of the pallet and fix the socket a lock ring. Establish the pallet.
4. Insert and tighten pallet bolts.
Cast part of the pallet
5. Clean being joined surfaces of a cast part and the block of cylinders.
	6. Put hermetic N15 03 295 in the areas specified in drawing.
	7. Establish laying in a flute on a cast part of the pallet and put a hermetic layer in thickness in 3 mm in the areas specified in drawing (see fig. Places of drawing of hermetic).
	8. Put hermetic N15 10 298 on places of joints (are specified by shooters) oil pump and block of cylinders.
	9. Put hermetic on places of joints (are specified by shooters) covers of the back radical bearing and the block of cylinders.
10. Establish a cast part of the pallet, insert and tighten bolts.
11. Establish the remained details.