Opel Omega

since 1993-1999 of release

Repair and car operation


Opel Omega
+ 1. Maintenance instruction
+ 2. Maintenance
- 3. Repair of engines
   + 3.1. SOHC engines in volume 2,0 liters
   - 3.2. DOHC engines in volume 2,0 liters
      3.2.1. Technical characteristics
      3.2.2. Compression check
      3.2.3. Top dead point (VMT) of the N1 piston
      3.2.4. Cover of camshafts
      3.2.5. Pulley of a cranked shaft
      3.2.6. Covers of a gas-distributing belt
      3.2.7. Gas-distributing belt
      3.2.8. Natyazhitel of a belt, asterisks and intermediate pulleys
      3.2.9. Epiploons of camshafts
      3.2.10. Camshafts and pushers
      3.2.11. Head of cylinders
      3.2.12. Oil pallet
      3.2.13. Oil pump
      3.2.14. System of an equilibration of a cranked shaft (engines since 1998)
      3.2.15. Flywheel
      3.2.16. Epiploons of a cranked shaft
      3.2.17. Engine and transmission fastenings
   + 3.3. Engines in volume 2,5 and 3,0 liters
   + 3.4. Partition of all petrol engines
   + 3.5. Diesel engine in volume 2,0 liters
   + 3.6. Diesel six-cylinder 2,5-liter engine
+ 4. Heating system and ventilation
+ 5. Fuel, exhaust systems
+ 6. System of start of the engine
+ 7. Ignition system
+ 8. Coupling
+ 9. Transmissions
+ 10. Main transfer, semi-axes
+ 11. Brake system
+ 12. Suspension bracket and steering
+ 13. Body
+ 14. Body electric equipment



3.2.12. Oil pallet

INTEGRAL OIL PALLET

Removal

PERFORMANCE ORDER
1. Disconnect a wire of the minus plug of the accumulator.
2. Lift and fix a forward part of the car.
3. Merge oil and tighten a cap of a drain opening.
4. Disconnect a wire from the sensor of level of oil on the oil pallet.
5. Unscrew the bolts, fixing basic arms to a transmission and the block of cylinders. Remove both arms and remove the bottom cover of a flywheel.
6. Braid nuts of the left and right support of the engine, remove an arm of the right support.
7. Fix the engine on the lift.
8. Unscrew bolts of the oil pallet and remove the pallet.
9. Remove a maslozaborny branch pipe and a dividing partition of the pallet.

Installation

PERFORMANCE ORDER
1. Carefully clean being joined surfaces of the pallet, the block of cylinders and the oil pump. Clean bolts of the pallet and a maslozaborny branch pipe.
2. Put hermetic N15 03 295 on being joined surfaces of the block of cylinders.
3. Put hermetic N15 10 181 on carvings of bolts of a maslozaborny branch pipe.
4. Establish a dividing partition and tighten bolts of a maslozaborny branch pipe.
5. Put hermetic on carvings of bolts of the pallet, establish the pallet and tighten bolts.
6. Establish the remained details.

COMPOUND OIL PALLET

Removal

PERFORMANCE ORDER
1. Disconnect a wire of the minus plug of the accumulator.
2. Lift and fix a forward part of the car.
3. Merge oil and tighten a cap of a drain opening.
4. Disconnect a wire from the sensor of the monitoring system of level of the car and disconnect a rod from sharnirny connection of the lever of the sensor.
5. Remove connecting draft of a steering drive.
6. Braid the nuts, fixing left and right support of the engine to a body.
7. Fix the engine on the lift.
8. Unscrew forward bolts of a cross-piece of a forward suspension bracket on four turns. Fix a back part of a cross-piece by means of a jack and unscrew back bolts. Lower a back part of a cross-piece approximately on 10 see.
9. If necessary disconnect a wire from the sensor of level of oil and, having removed a lock ring, press the sensor socket inside.
10. Unscrew bolts and remove the oil pallet together with laying.
11. Disconnect a wire from the sensor of temperature of oil and unscrew the bolts, fixing an arm of forward section of an exhaust pipe.
12. Unscrew the bolts, fixing a cast part of the pallet to a transmission and to the block of cylinders. Remove a cast part of the pallet.

Installation

PERFORMANCE ORDER
1. Carefully clean being joined surfaces of both parts of the pallet and the block of cylinders. Clean bolts of a cast part and a maslozaborny branch pipe.
2. Put hermetic N15 10 181 on carvings of bolts of a maslozaborny branch pipe and tighten bolts.
3. Put hermetic N15 03 295 on being joined surfaces of the block of cylinders.
4. Put hermetic on carvings of bolts of a cast part of the pallet, establish a cast part and tighten bolts.
5. Establish an external part of the pallet and tighten bolts.
6. Establish the remained details.