Opel Omega

since 1993-1999 of release

Repair and car operation

Opel Omega
+ 1. Maintenance instruction
+ 2. Maintenance
- 3. Repair of engines
   + 3.1. SOHC engines in volume 2,0 liters
   - 3.2. DOHC engines in volume 2,0 liters
      3.2.1. Technical characteristics
      3.2.2. Compression check
      3.2.3. Top dead point (VMT) of the N1 piston
      3.2.4. Cover of camshafts
      3.2.5. Pulley of a cranked shaft
      3.2.6. Covers of a gas-distributing belt
      3.2.7. Gas-distributing belt
      3.2.8. Natyazhitel of a belt, asterisks and intermediate pulleys
      3.2.9. Epiploons of camshafts
      3.2.10. Camshafts and pushers
      3.2.11. Head of cylinders
      3.2.12. Oil pallet
      3.2.13. Oil pump
      3.2.14. System of an equilibration of a cranked shaft (engines since 1998)
      3.2.15. Flywheel
      3.2.16. Epiploons of a cranked shaft
      3.2.17. Engine and transmission fastenings
   + 3.3. Engines in volume 2,5 and 3,0 liters
   + 3.4. Partition of all petrol engines
   + 3.5. Diesel engine in volume 2,0 liters
   + 3.6. Diesel six-cylinder 2,5-liter engine
+ 4. Heating system and ventilation
+ 5. Fuel, exhaust systems
+ 6. System of start of the engine
+ 7. Ignition system
+ 8. Coupling
+ 9. Transmissions
+ 10. Main transfer, semi-axes
+ 11. Brake system
+ 12. Suspension bracket and steering
+ 13. Body
+ 14. Body electric equipment

3.2.10. Camshafts and pushers

Removal

PERFORMANCE ORDER

	1. Remove a gas-distributing belt. Before removing a belt, turn a cranked shaft approximately on 60 ° back. The probability of contact of valves with pistons thereby decreases.
2. Remove asterisks of camshafts.
	3. Weaken and unscrew bolts of covers of bearings of a camshaft of inlet valves. Weaken bolts in turn, on a half of turn at one time. Get bolts and remove covers. For carrying out the correct installation during assembly all covers are numbered.
4. Remove a camshaft of inlet valves.
5. Similarly remove a camshaft of final valves.
	6. Take pushers and combine them in the separate numbered boxes.

Check

PERFORMANCE ORDER

1. Examine cams and it is necessary to replace necks of bearings of a shaft with existence of wear and damages, if necessary a shaft. Examine shaft bearings in a head of cylinders if they too are worn-out, replace a head of cylinders.

2. Examine pushers on existence of wear and damages. If necessary make replacement.

Installation

Places of drawing of hermetic

Put hermetic on the shaded areas (are specified by shooters).

Sequence of a tightening of bolts of covers of bearings of camshafts

PERFORMANCE ORDER

1. Grease pushers and openings of pushers with pure engine oil and establish pushers on the places.

2. Check, that the cranked shaft still was turned approximately on 60 ° back.

3. Grease cams and necks of bearings of shaft with pure engine oil. Establish camshafts in a head of cylinders. Establish covers of bearings.

4. Put hermetic N15 03 170 on a surface of a head of cylinders round covers of forward bearings of camshafts and in semicircular cuts in a back part of a head (see fig. Places of drawing of hermetic).

5. Tighten nuts of covers of a camshaft of inlet valves in the specified sequence in stages. Tighten covers very carefully, on a half of turn at one time (see fig. Sequence of a tightening of bolts of covers of bearings of camshafts).

6. Similarly tighten nuts of covers of a camshaft of final valves.

7. Establish new epiploons of shaft.

8. Establish asterisks of shaft and the remained details.