Opel Omega

since 1993-1999 of release

Repair and car operation



Opel Omega
+ 1. Maintenance instruction
+ 2. Maintenance
+ 3. Repair of engines
+ 4. Heating system and ventilation
+ 5. Fuel, exhaust systems
+ 6. System of start of the engine
+ 7. Ignition system
+ 8. Coupling
- 9. Transmissions
   + 9.1. Mechanical transmission
   - 9.2. Automatic transmission
      9.2.1. Technical characteristics
      9.2.2. Transmission liquid
      9.2.3. Gear shifting mechanism
      9.2.4. Gear shifting lever
      9.2.5. Epiploons
      9.2.6. Radiator of transmission liquid
      9.2.7. Electric elements of the monitoring system of a transmission
      9.2.8. Automatic transmission
+ 10. Main transfer, semi-axes
+ 11. Brake system
+ 12. Suspension bracket and steering
+ 13. Body
+ 14. Body electric equipment


9.2.7. Electric elements of the monitoring system of a transmission

GENERAL INFORMATION

SWITCH OF POSITIONS OF THE LEVER OF GEAR SHIFTING

Switch adjustment

1. Switch bolts

2. Cuts

3. Core

Removal

PERFORMANCE ORDER
1. Establish the gear shifting lever in neutral situation (N). Lift and fix a forward part of the car.
2. Unscrew the bolts, fixing forward section of an exhaust pipe and the catalytic converter to an intermediate pipe.
3. Remove heatisolating guards to get access to the central bearing of the driveshaft.
4. Unscrew two bolts, fixing the bearing to a body.
5. Disconnect a switch wire from the socket. Disconnect the socket from a transmission.
6. Uncover the switch.
7. Cкрутите a lock-nut (it is specified by an arrow) and disconnect switching lever of a transmission from a switching rod.
8. Establish a jack under a transmission and slightly raise it.
9. Unscrew the bolts, transmissions fixing a back cross-piece to a body.
10. Slightly lower a transmission to get access to switch bolts.
11. Unscrew bolts and remove the switch.

Installation

PERFORMANCE ORDER
1. Check, that the switching rod of a transmission was in situation (N).
2. Establish the new switch on switching rod and tighten bolts.
3. Adjust the switch.
4. Connect switching rod to the switching lever and tighten a lock-nut.
5. Connect to the socket a wire.
6. Fix the socket.
7. Tighten cross-piece bolts.
8. Establish the remained details.

Adjustment

PERFORMANCE ORDER
1. Establish the gear shifting lever in neutral situation (N). Lift and fix a forward part of the car.
2. Uncover the switch, braid a lock-nut and disconnect switching lever of a transmission from a switching rod.
3. In neutral situation, the cut in the case of the switch should coincide with a cut on an internal ring of the switch (see fig. Switch adjustment).

SWITCH OF THE SPORTS MODE OF THE TRANSMISSION

Removal

PERFORMANCE ORDER
1. Remove a cover of the lever of gear shifting.
2. Remove the switch from the top part of the lever.
3. Otpayayte of a wire from the switch.
4. Mark contacts and wires corresponding to them.

Installation

PERFORMANCE ORDER
1. Solder wires to switch contacts.
2. Establish the switch.
3. Establish a lever cover.

SWITCH OF THE WINTER MODE OF THE TRANSMISSION

Removal

PERFORMANCE ORDER
1. Remove a cover of the lever of gear shifting.
2. Remove the switch panel.

Installation

Installation is carried out to sequences, return to removal.

THE SWITCH OF THE MECHANISM OF SWITCHING ON THE LOW GEAR

Removal and installation

The switch is connected to a rope of an accelerator and separately does not act in film.

THE SWITCH OF THE LOCKING MECHANISM OF THE LEVER OF GEAR SHIFTING – LATE MODELS

Removal

PERFORMANCE ORDER
1. Remove the central part of the dashboard.
2. Remove forward and back arms of the back ventilating channel of a heater, remove the channel.
3. Disconnect wires and remove the switch (it is specified by an arrow) from a basic plate of the lever of gear shifting.

Installation

Installation is carried out to sequences, return to removal.

THE SOLENOID OF THE LOCKING MECHANISM OF THE LEVER OF GEAR SHIFTING – LATE MODELS

Removal

PERFORMANCE ORDER
1. Remove the gear shifting lever.
2. Disconnect solenoid grounding from a basic plate of the lever and disconnect a switch wire from the socket.
3. Unscrew screws and remove the solenoid (it is specified by an arrow).

Installation

Installation is carried out to sequences, return to removal.

THE SWITCH OF BLOCKING OF THE LOCK OF IGNITION – EARLY MODELS

Removal

PERFORMANCE ORDER
1. Remove the central part of the dashboard.
2. Remove forward and back arms of the back ventilating channel of a heater, remove the channel.
3. Disconnect a wire of the lever of gear shifting and a switch wire. Disconnect a wire of grounding of the switch from a lever arm.
4. Remove the switch (it is specified by an arrow).

Installation

Installation is carried out to sequences, return to removal.

ELECTRONIC CONTROL UNIT (ЭБУ)


Removal

PERFORMANCE ORDER
1. Disconnect a wire of the minus plug of the accumulator.
2. Remove a ware box.
3. Braid nuts and remove EBU. Disconnect block wires.

Installation

PERFORMANCE ORDER
1. Installation is carried out to sequences, return to removal.
2. If you establish the new block, address to the expert.

THE SENSOR OF THE CONDUCTED SHAFT OF THE TRANSMISSION

Removal

PERFORMANCE ORDER
1. The sensor (it is specified by an arrow) is established in a back part of a transmission.
2. Lift and fix a forward part of the car.
3. Disconnect a sensor wire.
4. Unscrew a bolt and remove the sensor.

Installation

Installation is carried out to sequences, return to removal.

ELECTROMAGNETIC VALVES OF THE TRANSMISSION

Removal and installation

Works on removal and installation of valves provide to the expert.